Fixed Gas & Flame Detection

Chillgard® VRF Refrigerant Leak Detector

MSA Chillgard VRF Refrigerant Leak Detector is the first industry detector for Variable Refrigerant Flow Systems (VRF) with integrated BACnet capability. Therefore, it can be directly connected with any Building Management Systems (BMS). MSA applies its proven Photoacoustic infrared sensing technology that provides a stable zero baseline, minimizes cross-sensitivities and offers low cost of ownership through minimum maintenance required.
view details

SB100 Ultrasonic Bump Tester

The SB100 is a hand-held battery-operated rechargeable ultrasonic tester designed to bump test General Monitors ultrasonic gas leak detectors. The SB100 is useful for quick tests where physical access to the ultrasonic gas detector can be difficult. The unit can be used to bump test up to 18 meters away from the detector in Class 1, Div 1&2 hazardous areas.
view details

Z-Gard® DS MPO Dual Gas Sensor

The Z-Gard DS MPO Gas Sensor connects directly to a building automation system for dual gas monitoring solutions. It detects the presence of carbon monoxide and nitrogen dioxide. The Z-Gard DS MPO Sensor communicates with one of several industry standard protocols, providing seamless integration with commercial automation systems.
view details

Z-Gard® S MPO Single Gas Sensor

The Z-Gard S MPO Gas Sensor connects directly to a building automation system for single gas monitoring solutions. It detects the presence of either carbon monoxide, nitrogen dioxide or combustible gases in air. The Z-Gard MPO Sensor communicates with one of several industry standard protocols, providing seamless integration with commercial automation systems.
view details

GasGard® 100 Control System

New GasGard 100 Control System scalable, high performance data acquisition/data-logging platform offers an intelligent approach to data acquisition and control for fixed flame and gas detection. Open Ethernet connectivity with web-based configuration and data monitoring functions allow GasGard 100 Controllers to provide a wide range of monitoring and historical logging functions. View real time trends via web browser from any PC without special software. Gasgard 100 Control System provides fully integrated measurement, display and recording platforms, that when equipped with MSA’s extensive line of transmitters and sensors, forms a complete gas detection solution.
view details

Ultima® Controller

The Ultima Controller is purpose-designed and built to provide complete access to all advanced features of the Ultima and Ultima X Gas Monitors, as well as the Toxgard II Gas Monitor. Via its full-function and password-protected keypad, users can set the real time clock, set alarm levels, change span-gas values, display date of last calibration, display minimum, maximum and average gas values, change address and set future calibration time/date in addition to providing basic calibration functions
view details

FlameGard® 5 MSIR Flame Detector

MSA's FlameGard® 5 MSIR Detector is an advanced multi-spectrum flame detector designed to provide superior false alarm immunity with the widest field of view. The detector employs a state-of-the-art multi-spectrum infrared (MSIR) sensor array with a sophisticated Neural Network Technology (NNT) system.
view details

Ultima® Calibrator

The Ultima Calibrator offers the industry's simplest, quickest calibration. Simple, three-button device is purpose-built for calibrating and changing the address of Ultima and Ultima X Gas Monitors and the Toxgard II Gas Monitor.
view details

FlameGard® 5 UV/IR Flame Detector

The precision-crafted FlameGard® 5 UV/IR Flame Detector monitors both ultraviolet and infrared (UV & IR) spectral ranges, which makes it highly immune to false alarms caused by lightning, arc welding, hot objects and other sources of radiation. The unit's Continuous Optical Path Monitoring (COPM) checks both the optical path integrity and the detector's electronic circuitry once a minute, while the wide field of view enables greater fire detection coverage.
view details

Ultima® X Sampling Module

Built for safety programs that demand gas concentration measurement before allowing entrance to an area, the Ultima X Sampling Module is exclusively designed to work with the Ultima X Gas Monitor. The unit features an explosion-proof design and reliably extracts a sample from any confined or inaccessible area—or any area that is too hot, cold, or otherwise harsh—and delivers gas concentration reading directly to the installed gas monitor.
view details

Z-Gard® CXII Controller

The robust Z-Gard CXII Controller connects with a wide array of MSA Z-Gard Sensors, accepting up to 99 sensors. A large backlit LCD screen displays operating, alarm and fault diagnostic system status. Modbus RTU or BacNet MS/TP digital protocols are available for integration with building automation systems.
view details

FlameGard® 5 UV/IR-H2 Flame Detector

The precision-crafted MSA FlameGard® 5 UV/IR-H2 Flame Detector monitors the ultraviolet and infrared spectral ranges to detect unwanted hydrogen fires. Its meticulous engineering and usage of UV and IR make it highly immune to false alarms caused by lightning, arc welding, hot objects and other sources of radiation. The unit's continuous Optical Path Monitoring (COPM) checks both the optical path integrity and the detector's electronic circuitry once a minute, while the wide field of view enables greater fire detection coverage.
view details

Ultima OPIR-5 Open Path Infrared Detector

Get continuous monitoring of methane, propane, and other combustible gases with this open path infrared detector. Provides 4-20 mA analog signals, as well as digital display and relay contacts. Digital display and adjustable mounting arms ensure easy alignment. Factory calibrated for low-maintenance operation.
view details

9010/9020 Controller

The 9010/9020 SIL controller comes with advanced design and innovative features. Monitoring up to 20 channels, it’s now also SIL 2 suitable. The 9010 controller operates with one independent sensor, while the 9020 operates with two independent sensors per control module. Each module comes with an independent AC/DC power supply for increased system reliability. Both units feature full internal diagnostics, which minimize false alarms and unexpected down time. The controller powers up the remote gas detectors, while its large four-digit LCD and LED provide crucial information such as gas concentration, alarm status and more. The 9010/9020 LCD controller monitors up to 20 channels and comes with an independent power supply. The LCD version has approvals for FM (North America) and CCCF (China) whereas the 9010/9020 SIL controller is ATEX and  SIL2 certified.
view details

Observer-i Ultrasonic Gas Leak Detector

Instantly detect pressurized gas leaks with this high-precision,  omni-direction acoustic detector utilizing Gassonic ultrasonic technology. Works even when traditional methods of gas detection are unsuitable or dependent on ventilation. Features Artificial Neural  Network (ANN) technology that distinguishes between real gas leaks and false  alarm sources without requiring any in-field training. The Observer-i UGLD provides an industry-leading detection range (up to 28 m) reducing the  number of detectors required. Ideal for use in complex, outdoor pipeline systems.
view details

FlameGard® 5 Test Lamp

With its high-energy broadband radiation source, the battery-operated FlameGard® 5 Test Lamp is precision-designed to test MSA's FlameGard® 5 MSIR, UV/IR, and UV/IR-H2 Flame Detectors. The rechargeable test lamp provides a radiation source that emits sufficient energy in both the ultraviolet and infrared spectra to activate UV and/or IR flame detectors. A variety of flashing test patterns allow the test lamp to check the operation of MSA flame detectors.
view details

Z-Gard® C 485 Controller

For wide-ranging gas-monitoring needs, the economical Z-Gard C 485 Controllers are up to the task. The controllers connect with a wide array of MSA Z-Gard S Sensors, with controller models accepting up to 24 sensors. Relay outputs indicate warning, alarm or sensor fail for each zone, and units are available with one or two zones. A large LED readout displays the active channel and the corresponding sensor gas level.
view details

Quad Gas® II Controller

Housed in a rugged, NEMA 4X enclosure, this microprocessor-based system links with up to four remote gas sensors. The large, four-digit LED display shows gas concentration and features four warning relays with one per sensor. The model also comes with four discrete alarm relays. Warning, alarm set-points and full-scale range of the sensor are set at the user-friendly keyboard, while a DC battery connection provides backup stability.
view details

Toxgard® II Gas Monitor

Simply connect the convenient ToxGard II Gas Monitor to a power source and a remote sensor, and it's ready to detect toxic gases, combustible gases and oxygen deficiency. The indoor/outdoor unit is housed in a rugged NEMA 4X enclosure and features a large LED screen, three levels of alarm and a failsafe fault relay output.
view details

Chemgard® Photoacoustic Infrared Gas Monitor Series

The stable, durable Chemgard Photoacoustic Infrared Gas Monitor is purpose-built and detects minute amounts of a wide variety of gases. Three different enclosure styles ensure there is a configuration for wildly different situations. The instrument typically draws the gas sample via an internal pump, which allows the unit to be mounted in a convenient location if the area to be monitored is inaccessible. The unit can be expanded to monitor up to 8 locations, while an easy-to-read display shows gas concentrations and 3 levels of alarms.
view details

MultiGard™ 5000 Multipoint Gas Sampling System

The economical, efficient MultiGard 5000 Gas Sampling System uses auto-standardization and flexible sample point order to analyze gas from up to 32 locations. Maintenance and calibration are made easy because all the work is performed at a single location, while also ensuring personnel don't have to enter the monitored area. The unit directly connects to Modbus TCP/BACnet IP networks, which allows communication to other equipment or controllers. The system allows secure viewing at one's personal computer. The screen provides easy access to scroll-down menus and visual indicators of sensor condition.
view details

Chillgard® LE Photoacoustic Infrared Refrigerant Monitor

The Chillgard LE Photoacoustic Infrared Refrigerant Monitor is specifically designed for reliable detection of five of the most common refrigerants from up to four remote locations—with a minimum detection level of 20ppm. Specifically designed to operate for months with virtually no zero drift.
view details

Z-Gard® COmbo Gas Monitor

A cost-efficient monitor for underground garages and ventilation control, the Z-Gard COmbo Gas Monitor uses a solid-state sensor to detect carbon monoxide. The unit features local audio/visual alarm status indicators and it can be configured to interface with air-handling equipment to control air quality within a building. Additional remote sensors can be attached to the unit via the RS-485 network port, while a 4-20mA output is proportional to the calibrated operating range.
view details

Ultima® X Series Gas Monitors with X3® Technology

The Ultima X Series Gas Monitors with X3 Technology bring the power of multi-sensing, signal boost and ModBus output to the Ultima X line of MSA gas monitors. The units are crafted from either stainless steel or NEMA 4X-rated plastic, and our patented sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification. The interchangeable smart sensors eliminate the need for reconfiguration, while the use of one circuit board increases reliability. Each sensor can be placed up to 3,000 feet from the monitor, while the scrolling LCD screen displays sensor reading and gas type.   Note: This is a custom product. Please consult your local sales manager or contact Customer Service for configuration details
view details

Ultima® XL/XT Series Gas Monitors

Engineered to provide cost-efficient gas detection, the Ultima XL/XT Series Gas Monitors are simply an outstanding choice. The units boast a hand-held HART port running over 4-20mA output provides convenient setup, calibration and diagnostics. The interchangeable smart sensors eliminate the need for reconfiguration, while local calibration employs LEDS and push-buttons. Indoors or outdoors, some of these explosion-proof models feature infrared technology that eliminates the need for frequent calibrations. Some units operations are based on dual-wavelength, heated-optics technology, which compensates for temperature, humidity and aging effects. The monitors use only one circuit board for increased reliability, and they're easy to install with two-piece field-wiring connectors.
view details

TRIGARD® Gas Monitoring System

Designed to meet a variety of demanding applications, from wastewater facilities, to light industry and commercial applications, the TRIGARD Gas Monitoring System features MSA's precision craftsmanship and detects chlorine, sulfur dioxide and other toxic and combustible gases. The adjustable-range unit also detects oxygen deficiency and enrichment. AC or DC powered, the system features a highly visible LCD screen and simple push-button calibration. Boasting sturdy NEMA 4X design and a single board, the unit offers multiple sensor mounting options. Our patented sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification, while interchangeable smart sensors are pre-calibrated for installation right out of the box.
view details

TriGas Monitoring System

The TriGas Monitoring System consists of up to three sensors with Ultima® X3 Technology’s digital communications with on-board LEDs and relays to provide local alarms. This TriGas system offers  interchangeable smart sensors, internal DC-powered sample-draw pump and a hydrophobic end-of-line filter that makes it  ideal for areas of wastewater treatment plants that are subject to flooding (such as wet wells). The TriGas Monitoring System typically monitors for oxygen, hydrogen sulfide and combustible gases (methane or petroleum vapors) and is specifically designed for optimum performance within high-moisture environments. This system can also be supplied with the proper options to meet the NFPA 820 section 1.8 standards followed by the wastewater industry.  
view details

Chillgard® NH3 Gas Monitor

The Chillgard NH3 Gas Monitor is the economical choice for fast, reliable detection of parts-per-million (ppm) levels of ammonia, down to -40°C. Capable of measuring a 10 ppm leak, with full-range scale of 0-1000 ppm.
view details
Discontinued Chillgard® RT Refrigerant Monitor

Chillgard® RT Refrigerant Monitor

Capable of detecting refrigerant gas down to 1ppm, the Chillgard RT Refrigerant Monitor is purpose-built to monitor up to eight remote areas—and is completely configurable to detect either a specific refrigerant or group of refrigerant gases.
view details
Product Comparison Queue (0) Compare Products