CalGard Remote Calibration Adapter
The CalGard Remote Calibration Adapter is a stainless-steel accessory for the ULTIMA X5000 and General Monitors S5000 (X/S5000) digital sensors that provides reliable operation of remotely installed gas detection sensors working under harsh environmental conditions. It permits users to complete function tests (“bump tests”) and calibrations without the need for directly accessing the sensor and greatly simplifies gas detector maintenance. It prevents dilution of the test gas going to the sensor even in high wind conditions.
Chillgard® 5000 Ammonia Monitor
The Chillgard 5000 Ammonia Monitor accurately detects ammonia gas leaks as low as 10 ppm for early notification, keeping your plant safe according to ANSI/IIAR and EN 378. Using Photoacoustic Infrared (PAIR) technology provides a more accurate measurement and requires less maintenance than traditional electrochemical gas sensors for lower cost of ownership.
Chillgard® 5000 Refrigerant Leak Monitor
The Chillgard 5000 Refrigerant Leak Monitor provides the earliest level of detection of costly refrigerant gas leaks in mechanical equipment rooms. Sampling system with patented photoacoustic infrared (PAIR) technology detects leaks as low as 1 part per million (ppm). Intuitive, touchscreen user interface makes it easy to operate. Predictive maintenance and diagnostics keep you operational.
Chillgard® 5000 Remote Display
The Chillgard® 5000 Remote Display provides gas monitor information before room entry where potentially hazardous gas levels may exist. It mimics the Chillgard 5000 Gas Monitor readings for gas concentration, alarm status, calibration.
FL500 UV/IR Flame Detector
The FL500 UV/IR Flame Detector monitors for radiation emitted by a flame in both the ultraviolet (UV) and infrared (IR) spectral ranges. This UV/IR combination provides a fast response time and increased false alarm immunity against sources of radiation for reliable protection.
FL500-H2 UV/IR Flame Detector for Hydrogen Applications
The FL500-H2 is an Ultraviolet / Infrared flame detector designed specifically to detect hydrogen (H2) fires. The FL500-H2 optical flame detector monitors for radiation emitted by a hydrogen flame in both the ultraviolet (UV) and infrared (IR) spectral ranges. This UV/IR combination provides a fast response time and increased false alarm immunity against sources of radiation for reliable protection.
General Monitors S5000 Gas Monitor
It operates over a wide temperature range using a variety of gas sensing technologies. Breakthrough XCell® gas sensors with TruCal® technology extends calibration cycles up to 24 months and actively monitors sensor integrity for ultimate peace of mind.
HazardWatch Fire and Gas System
An innovative, modular system that combines highly reliable programmable logic controller (PLC) technology with our advanced gas and flame field devices. It is highly scalable, making it suitable for small systems to large plant-wide applications. Offering intelligence, flexibility and reliability, the HazardWatch System's controller hardware configuration and software has been tested by Factory Mutual to verify NFPA 72 compliance.
Senscient ELDS™ Open Path Gas Detector
The Senscient ELDS laser-based open path gas detector is available for a wide range of toxic and flammable gases. The Senscient ELDS uses 'SimuGas' self-testing to eliminate employees entering hazardous areas for gas checks. Nuisance false alarms are virtually eliminated with its breakthrough Harmonic Fingerprint processing.
TG5000 Gas Monitor
The TG5000 Gas Monitor is an effective and economical solution to detecting combustible and toxic gases, as well as oxygen deficiency/enrichment, in wastewater, commercial and light industrial applications. The TG5000 helps personnel to work safely in these environments offering a variety of sensor and configuration options.
ULTIMA® X5000 Gas Monitor
The ULTIMA® X5000 Gas Monitor is the future of gas detection for oxygen, toxic and combustible gases. MSA XCell® gas sensors with TruCal® technology offer calibration cycles up to 24 months (local calibration respected). The gas transmitter's advanced, multi-lingual OLED display is easy to read and the unique touch-screen interface makes it simple to navigate.
FL4000H Multi-spectrum IR Flame Detector
The FL4000H is an advanced multi-spectrum infrared (MSIR) flame detector that provides superior false alarm immunity with the widest field of view. The FL4000H employs a multi-spectral optical IR sensing array with a sophisticated Neural Network Technology (NNT) system to reliably discriminate between actual flames and the vast majority of false alarm sources. The FL4000H detects typical fires such as alcohol, n-heptane, gasoline, jet fuels and hydrocarbons. It can also see through dense smoke produced by diesel, rubber, plastics and lube oil fires.
The SUPREMATouch features a large colour touchscreen display with a title-based menu structure to optimize intuitive operation. It can be used with a wide range of detectors for combustible gas, toxic gas and oxygen deficiency. Output options include relays and 4-20 mA outputs. Remote racks can be connected (satellite structure), which expands control systems and reduces cabling costs. Interfacing to external systems is provided by using Modbus or Profibus. The SUPREMATouch has been certified according to ATEX and is suitable for virtually any safety related application including redundant systems with up to a Safety Integrity Level (SIL) 3 rating (EN 61508). The intuitive SUPREMA Manager Software is intended for configuration, parameterization and calibration of the SUPREMATouch Fire and Gas Controller. It offers the option to create detailed and clearly laid out reports to support documentation and supports all the features of the SUPREMATouch. Note: This is a custom product. Please consult your local MSA distributor or contact MSA Customer Service for configuration details.
Simple, accurate calibration is easy with these economical, all-in-one kits. Choose from 14 different types for sensor and instrument calibration. Kits include zero and span cylinders, regulators, tubing, accessories and instructions. All kits housed in a lightweight carrying case, making it convenient to carry everything directly to the sensor location or job site.
GasGard® XL Controller
Monitor up to eight remote gas sensors with the highly accurate wall-mounted GasGard XL Controller. The controller's large, multi-language LCD display provides real-time readings, offers full-system diagnosis and shows intuitive icons. Housed in durable, fire-retardant ABS plastic, the controller is suitable for a variety of chemical, industrial and waste water environments. The sensor also features a buzzer that sounds up to 85 dB.
IR400 Point IR Gas Detector
The IR400 Infrared (IR) Point Detector is a hydrocarbon gas detector that continuously monitors combustible gases and vapors within the lower explosive limit (LEL) and provides alarm indication. It features an industry-leading response time of ≤ 3 seconds, even with a splash guard installed. All electronics are contained within an explosion-proof housing so that the IR400's detector information can be processed locally. Configurations with analog output, Modbus and HART are also available.
ModCon 75 Touch Controller
Designed for use with the Ultima® X Gas Monitor with X3 technology, the pre-programmed ModCon™ 75 Touch Controller features a 7” touchscreen monitor for ease of use. The controller is self-configuring for monitoring up to 25 monitors for a total of 75 sensors. The compact unit allows for remote control of many sensor/transmitter features. The controller is suitable for all industrial, municipal, oil, gas, petrochemical, and HVAC applications.
Chillgard® VRF Refrigerant Leak Detector
The Chillgard VRF Refrigerant Leak Detector is the first industry detector for Variable Refrigerant Flow Systems (VRF) with integrated BACnet capability. Therefore, it can be directly connected with any Building Management Systems (BMS). MSA applies its proven Photoacoustic infrared sensing technology that provides a stable zero baseline, minimizes cross-sensitivities and offers low cost of ownership through minimum maintenance required.
Z-Gard® DS MPO Dual Gas Sensor
The Z-Gard DS MPO Gas Sensor connects directly to a building automation system for dual gas monitoring solutions. It detects the presence of carbon monoxide and nitrogen dioxide. The Z-Gard DS MPO Sensor communicates with one of several industry standard protocols, providing seamless integration with commercial automation systems.
Z-Gard® S MPO Single Gas Sensor
The Z-Gard S MPO Gas Sensor connects directly to a building automation system for single gas monitoring solutions. It detects the presence of either carbon monoxide, nitrogen dioxide or combustible gases in air. The Z-Gard MPO Sensor communicates with one of several industry standard protocols, providing seamless integration with commercial automation systems.
The Ultima Controller is purpose-designed and built to provide complete access to all advanced features of the Ultima and Ultima X Gas Monitors, as well as the Toxgard II Gas Monitor. Via its full-function and password-protected keypad, users can set the real time clock, set alarm levels, change span-gas values, display date of last calibration, display minimum, maximum and average gas values, change address and set future calibration time/date in addition to providing basic calibration functions.
Ultima® X Series Gas Monitors
Designed to provide thorough, continuous monitoring of many hazardous gases, the indoor/outdoor Ultima X Series Gas Monitors offer excellent performance and MSA quality craftsmanship. DuraSource™ Technology offers extended sensor life, while HART provides convenient setup, calibration and diagnostics. HART also allows for existing component install and wiring to be used. A single circuit board increases reliability, while our patented sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification. The units are crafted from either stainless steel or polycarbonate, and the interchangeable smart sensors eliminate the need for reconfiguration. Our scrolling LCD screen display sensor reading and gas type, while the calibration process includes date stamping and the ability to calibrate locally or remotely.
The Ultima Calibrator offers the industry's simplest, quickest calibration. Simple, three-button device is purpose-built for calibrating and changing the address of Ultima and Ultima X Gas Monitors and the Toxgard II Gas Monitor.
SM5000 Sampling Module
Built for safety programs that demand gas concentration measurement before allowing entrance to an area, the SM5000 Sampling Module is exclusively designed to work with the Ultima X5000, Ultima XE and General Monitors S5000 gas monitors. The unit features an explosion-proof design and reliably extracts a sample from any confined or inaccessible area—or any area that is too hot, cold, or otherwise harsh—and delivers gas concentration reading directly to the installed gas monitor.
Z-Gard® CXII Controller
The robust Z-Gard CXII Controller connects with a wide array of MSA Z-Gard Sensors, accepting up to 99 sensors. A large backlit LCD screen displays operating, alarm and fault diagnostic system status. Modbus RTU or BacNet MS/TP digital protocols are available for integration with building automation systems.
Ultima® XIR Gas Monitor
The microprocessor-based, infrared Ultima XIR gas detector is precisely engineered to continuously monitor for combustible gases and vapors. The unit features DuraSource Technology, which offers improved IR life, and a HART port for easy output access. The explosion-proof stainless steel monitor works indoors or outdoors and features infrared technology that eliminates the need for frequent calibrations. Its operations are based on dual-wavelength, heated-optics technology, which compensates for temperature, humidity and aging effects. The unit uses only one circuit board for increased reliability, and the sensor life isn't reduced by exposure to gas. The LCD screen provides scrolling information, while optional quick-check LEDs provide increased visibility.
Zero Two Series Gas and Flame Detection System
Modular system offering the widest range of control cards for use in an integrated fire and/or gas detection system. The Zero Two Series system can monitor any combination of the following: combustible gas, H2S, toxic gas, ultrasonic, oxygen deficiency and flame detection. In addition, its open architecture allows the system to accommodate other sensing devices for tasks such as smoke detection, heat detection and manual call points.
TA102A Single Channel Combustible Trip Amplifier Module
The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display). A digital display indicates fault codes and set up options. Other features include: LED indications of status, as well as both open collector and relay outputs for fault, low alarm and high alarm.
4802A Zero Two Series Control Module for Combustible Applications
The 4802A is a single channel Combustible Gas Control Module that has been designed for use with General Monitors catalytic bead sensors. It is designed to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through the front panel interface. A digital display indicates gas concentration, fault codes, calibration cues and setup options. Other features: LED indications of status, as well as open collector and relay outputs.
610A Four Channel Combustible Gas Monitor
The 610A is a system for continuously monitoring combustible gas (hydrocarbon) concentrations in four locations. The system consists of four General Monitors remote catalytic bead sensing assemblies and a solid-state controller. The controller features four independent channels, each having its own circuitry. The 610A features a digital display of gas concentrations in % LEL (0-99% lower explosive limit) for each channel.
Catalytic Bead Sensors
The General Monitors catalytic bead gas sensors are well known for their sensitivity, reliability and longevity and make them the first choice for most users of the catalytic oxidation gas detection principle. Every component is manufactured in-house to ensure optimum performance. Careful matching of the active and reference elements ("beads") result in a sensor that has negligible zero drift with respect to changes in humidity, pressure, and temperature.
IR5500 Open Path Infrared Gas Detector
The IR5500 is an open path infrared (IR) gas detector that continuously monitors for flammable gas leaks over large open areas. It monitors in both the LEL-m and ppm-m ranges to detect both small and large leaks. The IR5500 offers the benefits of early detection with its high sensitivity to gas concentrations at the ppm levels. This feature allows it to alarm faster than an LEL-only detector. Digital display and adjustable mounting arms ensure easy alignment. Factory calibrated for low-maintenance operation.
580A Dual-Channel Combustible Gas Monitor
The 580A is a compact, highly-versatile system for continuously monitoring combustible gas (hydrocarbon) concentrations in two locations. The system consists of two remote catalytic sensing assemblies and a solid-state controller. The controller automatically displays the higher reading channel on a digital display, scaled from 0-100% LEL (lower explosive limit). Manual override switching permits readout of the low channel at any time.
TA202A Single Channel H2S Trip Amplifier Module
The TA202A is a single-channel H2S Trip Amplifier Module for use with our H2S Intelligent Sensors. It is designed to monitor H2S in parts per million (ppm) levels and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through front panel interface (mode / select switch and digital display).
Ultima OPIR-5 Open Path Infrared Detector
Get continuous monitoring of methane, propane, and other combustible gases with this open path infrared detector. Provides 4-20 mA analog signals, as well as digital display and relay contacts. Digital display and adjustable mounting arms ensure easy alignment. Factory calibrated for low-maintenance operation.
2602A Zero Two Series Control Module for H2S Applications
The 2602A is a single-channel H2S Control Module that has been designed to monitor H2S in parts per million (ppm) levels and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through front panel interface (mode / select switch and digital display). The digital display on the 2602A indicates hydrogen sulfide gas concentration, fault codes, calibration cues and setup options. Other features include LED indications of status, relay outputs for fault, low alarm and high alarm, and serial communications ports.
H2S Gas Sensors and Accessories
General Monitorsʼ hydrogen sulfide (H2S) sensors are solid state devices, designed and manufactured for long life and fast response. They are selective to H2S and remain unaffected by high concentrations of other substances like hydrogen, sulfur dioxide, and gasoline vapors, which are often present in facilities that process sour gas and crude oil. A high tolerance to a broad range of temperatures and humidity enable these sensors to operate in rugged environments, as does their capacity to withstand exposure to high H2S concentrations over short periods.
The 9010/9020 SIL controller comes with advanced design and innovative features for monitoring up to 20 channels. The 9010 controller operates with one independent sensor, while the 9020 operates with two independent sensors per control module. Each module comes with an independent AC/DC power supply for increased system reliability. Both units feature full internal diagnostics, which minimize false alarms and unexpected down time. The controller powers up the remote gas detectors, while its large four-digit LCD and LED provide crucial information such as gas concentration, alarm status and more. The 9010/9020 LCD controller monitors up to 20 channels and comes with an independent power supply. The LCD version has approvals for FM (North America) and CCCF (China) whereas the 9010/9020 SIL controller is ATEX and SIL 2 certified.
Observer® i Ultrasonic Gas Leak Detector
Instantly detect pressurized gas leaks with this high-precision, omni-direction acoustic detector utilizing Gassonic ultrasonic technology. Works even when traditional methods of gas detection are unsuitable or dependent on ventilation. Features Artificial Neural Network (ANN) technology that distinguishes between real gas leaks and false alarm sources without requiring any in-field training. The Observer® i UGLD provides an industry-leading detection range (up to 28 m) reducing the number of detectors required. Ideal for use in complex, outdoor pipeline systems.
TA502A Single Channel Trip Amplifier Module
The TA502A is a single-channel generic trip amplifier designed for use in Zero Two Series Gas and Flame Detection Systems. It is used to process the 0-22 mA signal from any field mounted transmitter.
CC02A Serial Communications Module
The CC02A Communications Card facilitates serial communications between each module in a Zero Two Series Flame and Gas Detection System and an external host computer, which allows fast access to operational and setup data registers. It supports a Burst Read feature that returns all registers of a module in a single transmission.
DT210 Eight Channel H2S Readout / Relay Module
The DT210 is an eight-channel Readout / Relay Module designed for use with up to eight of our remotely located H2S Intelligent Sensors. The front panel contains a digital display that indicates 0-20 ppm (parts per million), 0-50 ppm, or 0-99 ppm of the hydrogen sulfide gas monitored by the Intelligent Sensors.
RGC - Remote Gas Calibrator for Catalytic Bead Sensors
The Remote Gas Calibrator (RGC) allows calibration gas to be applied to a remotely located catalytic bead sensor from an easily accessible location. The RGC is used for blocking ambient air and redirecting methane to the catalytic sensor for calibration or testing sensor accuracy. The RGC tests or calibrates the General Monitors catalytic sensor with 50% LEL methane. The unit is capable of calibrating gas at wind velocities up to 50 mph. The RGC is used manually with a pressure regulator (P/N 80146-1) and is suitable for calibrating with any light hydrocarbon.
TL105 Test Lamp
The TL105 is a battery operated test lamp designed specifically to test General Monitors Flame Detectors. The TL105 is an explosion-proof test lamp that can be used with the FL4000H MSIR flame detector as well as any of the FL3100 Series Flame Detectors. The TL105 operates up to 35 feet from the flame detector.
FM002A Facilities Module
The FM002A is a facilities module that provides a range of common facilities for all Zero Two control modules housed in the chassis. The FM002A is plugged into the last slot on the right-hand side of the Zero Two chassis. It may be daisy-chained allowing one FM002A to serve up to 100 Zero Two modules in any combination.
PrimaX® IR Gas Transmitter
Every feature of the PrimaX IR Gas Transmitter is designed with reliability in mind to withstand the most challenging environmental conditions through out the product’s life. MSA’s PrimaX IR Gas Transmitter offers LEL (Lower Explosive Limit) combustible gas detection through a patented PrimaX Gas Transmitter IR dual source design. A redundant IR source provides reliability and uninterrupted monitoring should a source failure occur. Furthermore, the possibility of obscurations due to rain, fog, dirt, dust, and other environmental conditions is minimized due to dual source design.
RGC-IR - Remote Gas Calibrator for Point IR Detectors
The remote gas calibrator, RGC-IR, is designed to be permanently installed on a combustible IR gas detector. The RGC-IR provides protection from outside elements and allows the user to apply calibration gas (@ 50 psi) to the detector from a remote source.
Z-Gard® C 485 Controller
For wide-ranging gas-monitoring needs, the economical Z-Gard C 485 Controllers are up to the task. The controllers connect with a wide array of MSA Z-Gard S Sensors, with controller models accepting up to 24 sensors. Relay outputs indicate warning, alarm or sensor fail for each zone, and units are available with one or two zones. A large LED readout displays the active channel and the corresponding sensor gas level.
IN042 Four Zone Control Module
The IN042 is a four zone input module designed for use with two-wire field devices such as smoke or heat detectors, pull switches and manual callpoints. It is designed to monitor these devices and provide both status indication and fault / alarm outputs for each zone.
RGC-HT - Remote Gas Calibrator for High Temperatures
To verify the proper operation of a catalytic combustible gas sensor, it is necessary to periodically apply a gas of known concentration to the sensor. This is usually done manually at the site with gas supplied from a small lecture bottle. As the sensor reacts to the calibration gas, adjustments are made to the monitoring system to bring its calibration into agreement with the known concentration of the calibration gas. At times, sensors are mounted in inaccessible locations, requiring expensive catwalks or scaffolding to reach them. The High Temp Remote Gas Calibrator (RGC-HT) allows the calibration gas to be applied to the catalytic bead sensor from easily accessible locations. The RGC-HT is used for blocking ambient air and redirecting methane or other light hydrocarbon gases to the catalytic bead sensor for calibration or testing sensor accuracy in various environments. The RGC-HT tests or calibrates the General Monitors Catalytic Bead sensor with 50% LEL methane or other light hydrocarbon gas. The unit is capable of calibrating and detecting gases in various wind conditions (up to 45 mph) and temperatures (up to 200°C when used with high temperature sensor).
MD002 Monitored Driver Output Module
The MD002 is a monitored driver output module designed for four independent outputs requiring monitoring in their non-active state, such as extinguishing solenoids, beacons, horns, etc. Each driver is independent and has circuitry to monitor short and open circuits in field wiring.
Quad Gas® II Controller
Housed in a rugged, NEMA 4X enclosure, this microprocessor-based system links with up to four remote gas sensors. The large, four-digit LED display shows gas concentration and features four warning relays with one per sensor. The model also comes with four discrete alarm relays. Warning, alarm set-points and full-scale range of the sensor are set at the user-friendly keyboard, while a DC battery connection provides backup stability.
1701 Portable Test and Calibration Unit
The 1701 is a portable test and calibration unit used to verify the operation and calibrate certain ultrasonic gas leak detectors. Although the detectors do not require regular maintenance, the 1701 can be used to satisfy the requirements for regular plant maintenance. Further, the 1701 requires no electrical connection to the gas leak detector but is simply placed over the sensor head of the gas leak detector.
ZN002A Three Zone Control Module
The ZN002A is a Zone Control Module for the Zero Two Series Fire and Gas Detection System. The ZN002A provides zoning and voting functions for three separate and independent zones of gas and / or flame detection.
PS002 Power Supply
The PS002* power supply module provides sufficient power for 12 Zero Two Series Modules and their field devices. The PS002 slides into four channel slots and supplies the buss with +24 VDC. On the rear of the PS002, connections are provided for AC voltage in (line or neutral), for DC voltage in (battery backup), and for DC voltage out (+24 VDC). On the front panel there is a green LED for a Power ON indication. * Not available in Europe.
Toxgard® II Gas Monitor
Simply connect the convenient ToxGard II Gas Monitor to a power source and a remote sensor, and it's ready to detect toxic gases, combustible gases and oxygen deficiency. The indoor/outdoor unit is housed in a rugged NEMA 4X enclosure and features a large LED screen, three levels of alarm and a failsafe fault relay output.
Chemgard® Photoacoustic Infrared Gas Monitor Series
The stable, durable Chemgard Photoacoustic Infrared Gas Monitor is purpose-built and detects minute amounts of a wide variety of gases. Three different enclosure styles ensure there is a configuration for wildly different situations. The instrument typically draws the gas sample via an internal pump, which allows the unit to be mounted in a convenient location if the area to be monitored is inaccessible. The unit can be expanded to monitor up to 8 locations, while an easy-to-read display shows gas concentrations and 3 levels of alarms.
MultiGard™ 5000 Multipoint Gas Sampling System
The economical, efficient MultiGard 5000 Gas Sampling System uses auto-standardization and flexible sample point order to analyze gas from up to 32 locations. Maintenance and calibration are made easy because all the work is performed at a single location, while also ensuring personnel don't have to enter the monitored area. The unit directly connects to Modbus TCP/BACnet IP networks, which allows communication to other equipment or controllers. The system allows secure viewing at one's personal computer. The screen provides easy access to scroll-down menus and visual indicators of sensor condition.
Chillgard® LE Photoacoustic Infrared Refrigerant Monitor
The Chillgard LE Photoacoustic Infrared Refrigerant Monitor is specifically designed for reliable detection of some of the most common refrigerants from up to four remote locations—with a minimum detection level of 20 ppm. Specifically designed to operate for months with virtually no zero drift.
IR700 Point IR Carbon Dioxide Gas Detector
The IR700 Infrared (IR) Point Detector is a microprocessor-based carbon dioxide gas detector that continuously monitors for CO2 in ppm levels. All electronics are contained within an explosion-proof housing so that the IR700's detector information can be processed locally. The IR700 operates with a 4-20 mA signal, which is proportional to 0 to 100% full scale. Configurations with analog output, Modbus and HART are available. Modbus and HART data can be used for predictive maintenance.
Z-Gard® S Sensor
The Z-Gard S Sensor is designed to detect the presence of carbon monoxide, nitrogen dioxide and combustible gases in air. These sensors employ solid state, electrochemical or catalytic sensors which generate a representative output signal proportional to the calibrated operating range. All Z-Gard S Sensors are available with 2 output versions, a 4-20mA analog output, or an addressable RS-485 digital signal. Z Gard Sensors with RS-485 digital output are specifically designed to operate as a system with any Z-Gard CXII or C 485 Controller. Z-Gard Sensors with 4-20mA can be installed as stand-alone sensors typically integrated with the Z-Gard C Controller, or common commercial equipment including PLC, DCS, or building automation systems.
Z-Gard® COmbo Gas Monitor
A cost-efficient monitor for underground garages and ventilation control, the Z-Gard COmbo Gas Monitor uses an electrochemical sensor to detect carbon monoxide. The unit features local audio/visual alarm status indicators and it can be configured to interface with air-handling equipment to control air quality within a building. Additional remote sensors can be attached to the unit via the RS-485 network port, while a 4-20 mA output is proportional to the calibrated operating range.
Z-Gard® DS Sensor
The Z-Gard DS Sensor is designed to detect the presence of carbon monoxide and nitrogen dioxide gases in parking garages, vehicle storage areas or wherever else these two toxic gases could be found. These sensors employ electrochemical sensors which generate a representative output signal proportional to the calibrated operating range. All Z-Gard DS Sensors are available with 2 output versions, a 4-20mA analog output, or an addressable RS-485 digital signal. Z-Gard Sensors with RS-485 digital output are specifically designed to operate as a system with any Z-Gard CXII or C 485 Controller. Z-Gard Sensors with 4-20mA can be installed as stand-alone sensors typically integrated with the Z-Gard C Controller, or common commercial equipment including PLC, DCS, or building automation systems.
Ultima® X Series Gas Monitors with X3® Technology
The Ultima X Series Gas Monitors with X3 Technology bring the power of multi-sensing, signal boost and ModBus output to the Ultima X line of MSA gas monitors. The units are crafted from either stainless steel or NEMA 4X-rated plastic, and our patented SafeSwap sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification. The interchangeable smart sensors eliminate the need for reconfiguration, while the use of one circuit board increases reliability. Each sensor can be placed up to 3,000 feet from the monitor, while the scrolling LCD screen displays sensor reading and gas type. Note: This is a custom product. Please consult your local sales manager or contact Customer Service for configuration details
Ultima® XL/XT Series Gas Monitors
Engineered to provide cost-efficient gas detection, the Ultima XL/XT Series Gas Monitors are simply an outstanding choice. The units boast a hand-held HART port running over 4-20 mA output which provides convenient setup, calibration and diagnostics. The interchangeable smart sensors eliminate the need for reconfiguration, while local calibration employs LEDs and push-buttons. Indoors or outdoors, some of these explosion-proof models feature infrared technology that eliminates the need for frequent calibrations. Some units operations are based on dual-wavelength, heated-optics technology, which compensates for temperature, humidity and aging effects. The monitors use only one circuit board for increased reliability, and they're easy to install with two-piece field-wiring connectors.
TRIGARD® Gas Monitoring System
Designed to meet a variety of demanding applications, from wastewater facilities, to light industry and commercial applications, the TRIGARD Gas Monitoring System features MSA's precision craftsmanship and detects chlorine, sulfur dioxide and other toxic and combustible gases. The adjustable-range unit also detects oxygen deficiency and enrichment. AC or DC powered, the system features a highly visible LCD screen and simple push-button calibration. Boasting sturdy NEMA 4X design and a single board, the unit offers multiple sensor mounting options. Our patented sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification, while interchangeable smart sensors are pre-calibrated for installation right out of the box.
TriGas Monitoring System
The TriGas Monitoring System consists of up to three sensors with Ultima® X3 Technology’s digital communications with on-board LEDs and relays to provide local alarms. This TriGas system offers interchangeable smart sensors, internal DC-powered sample-draw pump and a hydrophobic end-of-line filter that makes it ideal for areas of wastewater treatment plants that are subject to flooding (such as wet wells).
Chillgard® NH3 Gas Monitor
The Chillgard NH3 Gas Monitor is the economical choice for fast, reliable detection of parts-per-million (ppm) levels of ammonia, down to -40°C. Capable of measuring a 10 ppm leak, with full-range scale of 0-1000 ppm.
S4000CH Combustible Gas Detector
The S4000CH Intelligent Sensor is a microprocessor-based transmitter designed for use with General Monitors industry-leading catalytic bead sensors. It monitors combustible gases and vapors within the lower explosive limit (LEL) and provides status indication and alarm outputs. Complies with ANSI/ISA 12.13.01-2000 performance requirements for combustible gas detectors. This product has been replaced by the S5000 Gas Monitor. See its many advantages here: msasafety.com/s5000.
MC600 Multi-Channel Controller
The MC600 is a microprocessor-based multi-channel controller that provides six channels of continuous gas detection. It can be configured as either a local gas detection system, or it can be networked to provide a large plant-wide distributed safety system. It is compatible with our hydrocarbon sensors, H2S sensors, as well as our S4000CH, S4100C, S4000TH, S4100T, IR400, IR5500, IR700, TS4000H, Observer, and Surveyor gas detectors.
FL3100H UV/IR Flame Detector
The FL3100H is an Ultraviolet / Infrared flame detector designed to detect fires and provide alarm outputs directly from the detector while maintaining false alarm immunity. It monitors in both the ultraviolet (UV) and infrared (IR) spectral ranges, making it highly immune to false alarms. The FL500 UV/IR Flame Detector is the replacement for the FL3100H detector. Learn all about its advanced performance specifications here.
2280A Four Channel H2S Gas Monitor
The 2280A is a system for continuously monitoring H2S gas concentrations in four locations. The system consists of up to four remote mounted sensors and a solid state controller. The controller consists of four independent channels, each having its own circuitry. With a digital display, the 2280A shows hydrogen sulfide gas concentrations in ppm (parts per million) in the ranges of 0-20, 0-50, or 0-99 ppm for each channel.
S4000TH H2S Gas Detector
The S4000TH Intelligent Gas Sensor is a microprocessor-based transmitter designed for use with General Monitors' thin film metal oxide semiconductor (TFMOS) sensors to detect H2S gas. The unit features one person calibration and can virtually self-calibrate by simply activating a magnetic switch and applying gas. It detects hydrogen sulfide in 0-20 ppm, 0-50 ppm or 0-100 parts per million (ppm) levels over a wide temperature range. This product has been replaced by the S5000 Gas Monitor. See its many advantages here: msasafety.com/s5000.
FL802 Multi-Channel Flame Detection Readout / Relay Display Module
The Model FL802 is a compact, reliable and versatile multi-channel flame detection readout/relay display module designed to monitor up to eight remote FL4000H or FL3100 Series detectors.
DC110 Eight Channel Combustible Readout / Relay Module
The DC110 is an eight-channel Readout / Relay Module designed to be used with up to eight of our remotely located Combustible Intelligent Sensors. The front panel contains a digital display that indicates 0-99% LEL (lower explosive limit) of the combustible gas being monitored by the Intelligent Sensors.
IR4000S Single-Point Gas Monitor
The IR4000S Single-Point Monitor is a display and user interface for the IR400 point IR gas detector. The monitor allows local calibration and displays gas concentration. Relays are optional. The relays provide output for Alarm, Warn, and Fault conditions. This product has been replaced by the S5000 Gas Monitor. See its many advantages here: msasafety.com/s5000.
IR4000M Multi-Point Gas Monitor
The IR4000M Multi-Point Gas Monitor can be used as an integrated combustible gas detection system, with capacity to connect eight point IR or open path gas detectors and read their status with one command. The highest current % LEL among all connected detectors is shown continuously during normal operation. An extensive set of menus are easily navigated using a magnetic switch to request the status and configuration data stored by the IR4000M. This product has been replaced by the S5000 Gas Monitor. See its many advantages here: msasafety.com/s5000.
Chillgard® RT Refrigerant Monitor
Capable of detecting refrigerant gas down to 1ppm, the Chillgard RT Refrigerant Monitor is purpose-built to monitor up to eight remote areas — and is completely configurable to detect either a specific refrigerant or group of refrigerant gases. The Chillgard 5000 is the replacement for the Chillgard RT. See how easy it is to upgrade here.
IR4000S-CO2 Single Point Gas Monitor
The IR4000S CO2 Single-Point Monitor is a display and user interface for the IR700 carbon dioxide gas detector. The monitor allows local calibration and displays gas concentration. Relays are optional. The relays provide output for Alarm, Warn, and Fault conditions. This product has been replaced by the S5000 Gas Monitor. See its many advantages here: msasafety.com/s5000.
Surveyor Ultrasonic Gas Leak Detector
The Surveyor detects gas leaks by sensing the airborne ultrasound emitted from leaking gas at high pressure. Ultrasonic gas detection is based on robust and proven Gassonic technology and designed for long and failsafe operation in extreme environmental conditions. Because the Surveyor responds to the source of a gas release rather than the dispersed gas, it is unaffected by changing wind directions, gas dilution, and the direction of the gas leak. Looking for an ultrasonic gas leak detector? Explore the many benefits of the Observer-i Ultrasonic Gas Detector.
SMC 5100-02-IT Combustible Monitor
The SMC 5100-02-IT gas sensor monitors combustible gases such as Methane, Hydrogen, Propane, and others. It is based on catalytic bead technology, a consistent and reliable method of detection that offers excellent response times to the target gases. The 5100-02-IT sensor offers multiple communication outputs including 4-20 mA and Modbus RTU.
SMC 5100-28-IT Point Infrared Gas Detector
The SMC 5100-28-IT detector uses infrared technology, an accurate and stable gas detection method that is low maintenance and can operate in highly combustible and/or low oxygen environments. The 5100-28 IR detector is network-enabled to provide the interface needed to your plant-wide control system, whether it be 4-20 mA, Modbus, HART, relay contacts or SentryBus.
SMC 4101-28 Point Infrared Combustible Gas Detector
The SMC 4101-28 IR Gas Detector is a ruggedized instrument designed specifically for monitoring methane in high-vibration environments. It is built to meet extreme operating conditions in remote locations. The 4101-28 is fully certified to meet the stringent and code-compliant standards of UL 2075 as outlined in the International Fire Code.
SMC 5100-XX-IT Toxic Gas Detector
The SMC 5100-XX-IT gas detector monitors toxic gases such as Hydrogen Sulfide, Carbon Monoxide, Nitrogen Dioxide, Ammonia, Oxygen Deficiency, and others. The detector requires calibration only every six months, cutting operating costs and time. As part of the SMC Sentry IT platform, the detector can be remotely diagnosed and calibrated via Remote Sensor Capability.
SMC 5100-88-IT Infrared CO2 Gas Detector
The SMC 5100-88-IT detector monitors Carbon Dioxide, a toxic gas that can be dangerous in enclosed areas. The sensor monitors for indoor air quality to ensure a healthy, comfortable, and productive work environment. With non-intrusive calibration and remote sensor configuration, facility managers can easily calibrate and configure the sensor in hard to access areas.
SMC 4501-XX Toxic Gas Detector
The SMC 4501-XX Detector monitors toxic gases such as Hydrogen Sulfide, Carbon Monoxide, Oxygen Deficiency, Chlorine Dioxide, and others. Utilizing 2-wire loop-powered technology, the 4501-XX requires less wiring, leading to better protection from wiring errors. The 4501-XX requires minimal maintenance with a 6-month calibration cycle and continuous self-diagnostics.
SMC Sentry IT 32 Channel Controller
The SMC Sentry IT Controller is a powerful network-enabled hazardous gas detection system that operates up to 32 detectors and interfaces with devices over Modbus RTU, 4-20 mA, Sentry PSG Bus, and conventional dry contact. The embedded web application enables users to view important data remotely and provides connectivity into the Industrial Internet of Things (IIoT).
SMC Sentry IT Retrofit
SMC Sentry solutions are installed in thousands of facilities that face risks from combustible and toxic gases. New advances in sensing algorithms, protocols, web technologies and cloud connectivity can help enhance safety, reduce ongoing operational costs and provide new data driven insights. The SMC Sentry IT Retrofit makes it easy to upgrade legacy Sentry systems.
The SMC Sentry InSite is an intuitive web-based monitoring application that provides users with the ability to locally and remotely access their facility's fire and gas safety system online. InSite provides full monitoring of a SMC Sentry IT Controller and all connected detectors through a series of well-defined, auto-generated web pages.
SMC 3100 Series Flame Detector
The SMC 3100 Series Flame Detector utilizes a tri-spectra design (UV, IR and visible light spectrums) to provide continuous and reliable flame detection. The 3100 Series design provides the ability to detect flames from both hydrocarbon and non-hydrocarbon sources, making it ideal for a facility where the flame source could be generated from a variety of gases.
SMC 3200/3300 UV/IR Wet Bench Flame Detectors
The SMC 3200/3300 Series Flame Detectors utilize proven, stable UV/IR technology to continuously monitor for flames in wet bench and commercial applications. Due to its compact size, it is also used for installation in certain production equipment. The detectors can detect gasoline (heptane), polypropylene, isopropyl alcohol, MEK, hydrogen and silane fuel sources.
SMC 2350/2360 Telecom Gas Monitors
The SMC 2350/2360 Telecom Gas Monitors both continuously monitor for the presence of Carbon Monoxide (CO), but the Model 2360 also monitors for combustible gases. These hazardous gases are monitored in confined spaces in telecom sites, such as utility enclosures, to reduce the hazard of gas explosion and to maintain personnel safety.
SMC 2400 Vault Gas Monitor
The SMC 2400 Vault Gas Monitor detects combustible and carbon monoxide gas leaks to reduce the hazard of gas explosion and to maintain personnel safety. The monitor offers the gas detection functions required by telecom site managers including uninterrupted power supply, long-life sensors, five alarm relays, and both audible and visual alarm indication.
SMC 2450 Facility Environment Controller
The SMC 2450 Facility Environment Controller is designed to manage HVAC controls, environmental alarms, and manage rigorous personnel safety requirements of controlled environment vaults (CEVs) and walk-in cabinets. The SMC 2450 also monitors CEVs for the presence of combustible and toxic gases and automatically initiates ventilation when an alarm threshold is exceeded.